FAXON MATCH SERIES GUNNER PROFILE 10.5" 1:8T PISTOL-LENGTH 300 BLK AR15 BARREL
FaxonNot sure if this is the right 300 Blackout barrel?
We built a complete guide covering barrel length, twist rate (1:5 vs 1:8), suppressed performance, and series differences.
Description
Rifle Barrels › Match Series › 300 BLK › 10.5″ Gunner, 1:8, Pistol-Length | Works with: .750″ gas block • pistol gas tube • Gunner Lightweight BCG • 5/8x24 muzzle devices • .30 cal suppressors
Why a 10.5″ 300 Blackout
300 Blackout was designed to do its work from a short barrel. At 10.5″, supersonic loads run close to full potential, about 2,180 to 2,230 fps with 110 gr bullets, and subsonics stay above 1,000 fps, so it is the length to pick when you want one short gun that hunts with supersonics and runs quiet with subsonics.
It is the longest of Faxon’s short Match 300 BLK barrels and the one that gives up the least velocity.
Go deeper: 300 Blackout Barrel Buyer’s Guide • All 300 BLK barrels
Why a 1:8 Twist
1:8 is the standard 300 Blackout twist. It stabilizes typical lead-core subsonics, including 220 gr match bullets, and every common 110 to 125 gr supersonic, and the slower spin is gentle on thin-jacketed supersonic bullets at 10.5″ velocities. Long 220 to 240+ gr monolithic subsonic solids want a faster twist such as Faxon’s Match 1:5.
| 110–125 gr supersonic | Fully stable |
| 190–220 gr lead-core subsonic | Fully stable |
| 220–240+ gr monolithic solids | Marginal; choose a 1:5 |
Velocity from 10.5″
Published chronograph data from 10.5″ barrels.
| Load (fps) | 10.5″ |
|---|---|
| Barnes 110 gr TAC-TX | 2,181–2,189 |
| Hornady 110 gr V-Max | 2,229 |
| 125 gr SMK | 1,983 |
| Hornady 190 gr Sub-X | 1,082 |
| 220 gr OTM (suppressed) | 1,006 |
Sources: Lucky Gunner (2026) and Shooting Times 10.5″ tests. Estimates, not Faxon testing.
The Gunner Profile and Pistol-Length Gas
Faxon’s Gunner profile puts steel where a barrel needs stiffness, at the chamber and under the handguard, and trims it out front, so you get Government-profile durability with close to Pencil-profile handling. Pistol-length gas gives a short barrel enough dwell time to cycle reliably, with or without a suppressor.
At 10.5″, it is under 16″, so it builds an AR pistol or a registered short-barreled rifle unless a muzzle device is permanently attached to bring the barrel to 16″.
What “Match Series” Means
Match Series is Faxon’s 416-R stainless line. 416-R machines cleanly and holds a consistent bore, and Faxon button rifles it with 5R rifling, five lands with sloped sides instead of sharp-cornered ones, which deforms the bullet less and fouls less. Then the barrel is salt-bath QPQ nitrided inside and out. Nitride is a diffusion treatment, not a plating: it hardens the bore surface and adds corrosion resistance while adding virtually nothing to the dimensions, a few ten-thousandths of an inch, roughly a tenth the width of a human hair. It needs little to no break-in.
How it compares to Faxon’s other lines: the Duty Series is 4150 CMV with the same nitride finish, the hard-use option; the MATCH-X Series takes 416-R further with a honed and lapped bore and an uncoated exterior; and the Combat Series offers classic configurations with chrome-lined bores and manganese phosphate.
What’s in the Box
INCLUDED
10.5″ Match Series barrel
416-R stainless, QPQ nitride, 5R 1:8 twist, laser-marked “.300 BLK 1-8T”
INCLUDED
NP3 barrel extension
M4 feed ramps. Nickel-Teflon (NP3) coated, installed at 150 ft-lb, pinned, and headspaced.
NOT INCLUDED
Gas block, tube, muzzle device
.750″ gas block, pistol-length gas tube, 5/8x24 muzzle device. See Build It Out below.
Specifications
| Cartridge / chamber | 300 Blackout, CMM-checked chamber |
| Length | 10.5″ |
| Profile | Gunner |
| Weight | 1.1 lb |
| Twist / rifling | 1:8 RH, 5R button rifled |
| Material | 416-R stainless steel |
| Finish | Salt-bath QPQ nitride, bore and exterior |
| Gas system | Pistol-length; .104″ port, reamed to size |
| Gas journal | .750″, 1.9″ long |
| Muzzle | 5/8x24, target crown |
| Extension | M4 feed ramps, NP3 nickel-Teflon, torqued to 150 ft-lb, pinned |
| Headspace | 100%, 300 Blackout go/no-go gauge |
| Full-auto | Full-auto capable; see the heat guidance in the FAQs |
| Made in | Greater Cincinnati, Ohio, USA |
| Warranty | Faxon Lifetime Guarantee |
Fitment
| Upper receiver | Mil-spec AR-15 upper; Faxon Enhanced Forged Upper |
| Bolt carrier group | Standard 5.56 bolt and BCG; 300 BLK-marked 5.56 magazines; Faxon Gunner Lightweight BCG (pair a lightweight carrier with an adjustable gas block) |
| Gas block | .750″ (1.9″ journal): adjustable or fixed |
| Gas tube | Pistol-length |
| Muzzle device | 5/8x24: MuzzLok® Plan B Compatible Flash Hider 5/8x24, 5/8x24 Direct Thread to HUB Adapter |
| Handguard | Free-float; the muzzle sits about 9.8″ ahead of the receiver face, so a Streamline 9″ or shorter leaves room for a muzzle device |
How It’s Made
- Drill and ream: The 416-R bar is gun-drilled and pull-reamed.
- Button rifle: 5R button rifled, right-hand 1:8 twist.
- Air gauge: Bore air gauged.
- Stress relieve: Stress relieved at the blank stage, then qualified true to the bore.
- Profile, thread, crown: Gunner profile turned, .750″ journal held concentric to the bore, 5/8x24 threads cut, target crown.
- Chamber: 300 Blackout chamber cut and CMM-checked.
- MPI and nitride: Wet magnetic particle inspected, then salt-bath QPQ nitrided inside and out.
- Port and extension: .104″ gas port drilled and reamed; NP3 extension torqued to 150 ft-lb, pinned, and 100% headspaced.
- Mark and inspect: Laser-marked “.300 BLK 1-8T”, then final inspection of the crown, feed ramps, chamber, and threads.
How We Inspect It
Faxon barrels are built to a written control plan, and each run is logged on inspection sheets. Here is what this barrel goes through before it ships.
| Borescope | Every barrel, three times: after reaming, after rifling (no tearing, sharp rifling corners), and after chambering |
| Air gauge | Bore and groove diameters air gauged at several points along the bore; twist rate and groove count verified |
| Chamber | Checked on the CMM against a dedicated chamber program for the cartridge, first and last barrel of every run; chamber finish verified with a profilometer |
| Threads | Every muzzle thread gauged |
| Extension and headspace | Barrel extension torqued to 150 ft-lb, then every barrel headspace gauged |
| Magnetic particle | Every barrel, 100% wet magnetic particle inspected for flaws |
| First article | Full CMM first-article inspection after any machine maintenance, tool change, or part change, and at least every 30 days |
| Certifications | Material certs checked at receiving; stress relief and nitride certified by lot |
What Reviewers and Owners Say
“This is hands down one of the best 300 blackout barrels I have shot. It’s accuracy and reliability are above all of its competitors. And it looks good too.”
David Brogdon, FaxonFirearms.com
“Super accurate which i expect from faxon...great job”
Rob, FaxonFirearms.com
“I use this barrel regularly in our custome builds. customers think its great!”
LARRY, FaxonFirearms.com
BROWNELLS
Match 300 Blackout Gunner Barrels ›
Brownells carries the 10.5″ 1:8 with the 6″, 7.5″, and 9″.
“Stacking shots through the same hole at that distance.”
SHOOTING SPORTS RETAILER
Gold Award, Favorite Aftermarket Barrel ›
Retailers vote on the barrels they sell and stand behind. Faxon AR-15 and AR-10 barrels have won the Gold every year since 2022.
“A testament to our team’s dedication to crafting the best barrels on the market.”
Average ratings, out of 5 stars: 4.7 on FaxonFirearms.com; 5.0 at Brownells (Faxon 300 BLK Match listing).
Build It Out: Faxon Parts That Fit This Barrel
GAS BLOCK & TUBE .750″ gas block, pistol-length tube. Adjustable is recommended for suppressed use. | Patented Adjustable .750″ Gas Block › • .750″ Fixed Gas Block › • Pistol-Length Gas Tube › |
BOLT CARRIER GROUP Standard 5.56 bolt and BCG; 300 BLK-marked 5.56 magazines. | Gunner Lightweight BCG › • M16 BCG, Nitride › |
SUPPRESSOR .30 cal HUB-mount cans. | HARMONIX® ION .30 › • HARMONIX® Sentry .30 › • CORESYNC® .30 › |
MUZZLE & MOUNT 5/8x24 thread. | MuzzLok® Plan B Compatible Flash Hider 5/8x24 › • 5/8x24 Direct Thread to HUB Adapter › |
UPPER & HANDGUARD AR-15 upper; free-float handguard. | Enhanced Forged Upper › • Streamline 9″ Handguard › • Upper Builder › |
Compare Faxon Match Series 300 BLK Barrels
| Barrel | Twist / gas | MSRP |
|---|---|---|
| 10.5″ Gunner (this barrel) | 1:8, pistol-length | $197 |
| Match 7.5″ 1:5 | Faxon’s best-selling barrel | $189 |
| Match 9″ 1:5 | Suppressed hunting, any bullet weight | $196 |
| Match 9″ 1:8 | Standard twist, shorter package | $195 |
Match Series 10.5″ 300 BLK FAQs
1:8 or 1:5 for 300 Blackout?
Choose this 1:8 for lead-core subsonics and a lot of jacketed supersonics. Choose a Faxon Match 1:5 if you shoot the long 220 to 240+ gr monolithic subsonic solids.
What gas block and gas tube does it take?
A .750″ gas block on the 1.9″ journal and a pistol-length gas tube. Faxon’s patented adjustable .750″ block is the recommended pick, especially suppressed. The gas port is .104″, reamed to size.
Will it run suppressed and unsuppressed?
Yes. A suppressor adds back-pressure, so Faxon recommends its patented adjustable gas block: tune it for your can and ammunition, then open it back up when you shoot unsuppressed. If you run a lightweight carrier, always pair it with an adjustable gas block.
How is Match Series different from Duty Series and MATCH-X?
Match Series is 416-R stainless with 5R rifling and QPQ nitride inside and out. Duty Series is 4150 CMV with the same nitride finish. MATCH-X is 416-R with a honed and lapped bore and an uncoated exterior. All are made in Greater Cincinnati.
Is the nitride inside the bore?
Yes. Salt-bath QPQ nitride is a diffusion treatment, not a plating, so it hardens the bore and exterior while adding virtually nothing to them: the surface grows by a few ten-thousandths of an inch, roughly a tenth the width of a human hair. It needs little to no break-in.
Does it come with a gas block, gas tube, or muzzle device?
No. It ships with the nickel-Teflon extension installed, torqued to 150 ft-lb, pinned, and headspaced. Gas block, gas tube, and muzzle device are sold separately; the muzzle is threaded 5/8x24.
Is it full-auto capable, and how much heat can it take?
Yes. Like every Faxon nitrided rifle barrel, it is full-auto capable. The barrel is stress relieved, magnetic particle inspected for flaws, and salt-bath nitrided at roughly 1,050°F, so the steel and the nitride are stable far beyond normal firing temperatures. What limits any barrel on automatic fire is heat. A good guideline, drawn from U.S. military guidance for the M4 carbine: about 12 to 15 rounds a minute can be fired indefinitely, and continuous rapid fire should stop at about 150 rounds so the barrel can cool. Short barrels heat up faster than a 16″ rifle barrel, so expect to reach those limits sooner. Push past that and throat wear speeds up, which shortens barrel life. If the barrel smokes or starts to glow, stop: near 1,000°F the steel is approaching the temperature it was nitrided at, where it can begin to soften and the nitride can lose hardness, and military testing has seen M4 barrels fail at about 1,360°F. A hot chamber can cook off a round in as little as 10 seconds, so clear it quickly or keep it pointed in a safe direction. And heat affects accuracy in every barrel: groups open up as it heats. Faxon’s stress relieving and machining keep point of impact from walking, but let it cool before you check zero or shoot for groups.
Is a 10.5-inch barrel legal?
A barrel under 16″ makes the firearm an AR pistol or a short-barreled rifle, depending on how it is configured. Know and follow federal, state, and local laws before you build.
Where is it made, and what is the warranty?
Made in Greater Cincinnati, Ohio, and covered by the Faxon Lifetime Guarantee.
Finish the build
Add the gas block that lets you tune for your ammunition and suppressor, then build the rest around this barrel.
Adjustable .750″ Gas Block › Gunner Lightweight BCG › 300 Blackout Barrel Buyer’s Guide ›
Full-auto heat guidance is general, based on published U.S. military rate-of-fire guidance and steel and nitride data, not Faxon testing; barrel life under automatic fire depends on rate of fire, ammunition, and cooling. Velocity, stability, and energy figures come from published ammunition-maker and independent test data, not Faxon testing; results vary with ammunition, barrel, and conditions. MuzzLok®, HARMONIX®, CORESYNC®, and Flame Fluted® are trademarks of Faxon Firearms. Know and follow all federal, state, and local laws.
Warranty
Faxon Lifetime Guarantee. Covers manufacturing and material defects to the original purchaser. Excludes damage from misuse, neglect, non-standard ammunition, or modifications. Register your product at faxonfirearms.com/product-registration to expedite service. For purchases through dealers or distributors, warranty repairs are handled directly by Faxon Firearms; refunds must be processed through the selling entity. Full policy: faxonfirearms.com/warranty-privacy-terms/Customers Also Shopped These Items
Reviews
-
FAXON MATCH SERIES GUNNER PROFILE 10.5" 1:8T PISTOL-LENGTH 300 BLK AR15 BARREL
Excellent as always
-
Love Faxon Barrels
Build quality and fit are spot on! Another great product from Faxon
-
Good, but not great...
This was my first .300 barrel, and I was relatively new to firearms. Reading the specs list, this seemed like an absolute killer value for the price. Many rounds downrange, and a few more builds under my belt later, I have a couple of gripes. First, this barrel is overgassed, or at least mine was! I understand that needing to be able to reliably cycle rounds ranging from 110-220 (standard factory load) grains is pretty tricky to exactly nail, and it's better to be over than under-gassed. That said, the barrel that I have 'upgraded' into handles 110's and 220's just as reliably, and is less gassy. Second, I'm not sure this "gunner" profile is all that great... The aforementioned barrel I 'upgraded' into is a fully heavy contour, and I am none the wearier after a 4-hour day at the range. The heavy contour also maintains accuracy over fire schedules better than this barrel does. I'm certainly no expert, so take my review with a grain of salt. All this said, you really won't find greater bang for your buck than this barrel. I would just say plan on sticking to subs though if you intend to run a can, which is what this barrel has been completely relegated to now.
-
go to 300 bo barrel
I use this barrel regularly in our custome builds. customers think its great!
-
Match Series 10.5"Gunner 300 BLK Barrel
Great quality and finish. The Nickel Teflon extension is one of the best I've seen on any barrel. The fit on my VLTOR upper is tight and solid. Best fit of ANY barrel Ive installed on an AR upper. Stupid accurate at 50 Yds. as it is at 100 Yds. I am very happy with the results. Faxon knocks it out of the park with their Match Series. I will be purchasing another Match Series barrel soon!!!
-
Amazing Barrel
This is hands down one of the best 300 blackout barrels I have shot. It's accuracy and reliability are above all of its competitors. And it looks good too.
-
Loved it
Very pleased with my Faxon barrel super light looks and feels amazing definite 10/10 and highly recommended
-
10.5 Gunner barrel
The barrel have look and feel like high quality. The fit into my Anderson upper was very tight which is a good thing. I have yet to put any rounds through the barrel as I'm still in the middle of my build.
-
300 blk
Super accurate which i expect from faxon...great job