FAXON DUTY SERIES 11.5" GUNNER MID-LENGTH 5.56 COMPLETE UPPER - SUPPRESSOR READY

AR15 Upper Receivers › Complete Uppers, Suppressor Ready › Duty Series 11.5″ 5.56

What’s on This Upper

Every major part is a Faxon part that is also sold on its own; each card links to its product page, specs, and reviews.

Not included: lower receiver, suppressor, Plan B to HUB adapter, optic.

Barreled, Complete, or Suppressor Ready?

Faxon builds each upper in up to four configurations. A barreled upper has the receiver, barrel, gas system, handguard, and muzzle device installed, with no bolt carrier group or charging handle. A complete upper adds both, so it is ready to pin to a lower. Suppressor ready versions swap in a MuzzLok® Plan B compatible flash hider and, on gas guns, Faxon’s patented adjustable gas block, so a suppressor mounts with one adapter and the gas can be tuned to it. This one is the complete upper, suppressor ready.

What a 5.56 Upper Needs

The 5.56 NATO chamber fires 5.56 NATO and .223 Remington, and the 1:8 twist stabilizes everything from 55 gr FMJ through 77 gr match bullets.

Suppressor Ready, Explained

Adjust with the rifle unloaded and the block cool. Suppressor purchase requirements are listed on each suppressor’s page; federal, state, and local laws apply.

Why a Lightweight Carrier Gets an Adjustable Gas Block

A lighter carrier needs less gas to cycle, and a suppressor adds back-pressure. Without a way to reduce gas, the bolt runs fast and hard: more recoil, more gas to the face, and more wear on the carrier, extension, and buffer. Faxon’s rule runs one way: if a build gets a lightweight carrier, it gets an adjustable gas block. This upper has both, so you tune it once for your ammunition and suppressor and it runs soft.

How It’s Built and Inspected

Finish the Rifle

This upper pins to any mil-spec AR-15 lower. Faxon makes three, all from 7075-T6 forgings with an upper-to-lower tensioning screw to take out receiver play. The lower is the serialized part, so it ships to an FFL; the upper doesn’t.

What Reviewers and Owners Say About These Parts

This upper is new, so it has few reviews of its own yet. Every major part on it is sold on its own, so here is what independent reviewers and Faxon customers have said about the barrel, carrier, handguard, gas block, and receiver.

Average ratings on FaxonFirearms.com, out of 5 stars: 11.5″ Gunner 5.56 barrel: 4.8; BCG: 5.0; gas block: 5.0; upper receiver: 4.9.

Compare the Duty Series 11.5″ 5.56 Uppers

Duty Series 11.5″ 5.56 Complete Upper, Suppressor Ready FAQs

What comes on this upper, and what doesn’t?

Included: Enhanced Forged AR-15 upper, 11.5″ Duty Series Gunner 5.56 barrel, 10.75″ Streamline aluminum M-LOK handguard, patented adjustable .625" low-profile gas block, mid-length stainless gas tube, MuzzLok® Plan B compatible flash hider, 5.56 Gunner Lightweight BCG, nitride, mil-spec AR-15 charging handle. Not included: lower receiver, suppressor, Plan B to HUB adapter, optic.

What’s the difference between a barreled upper and a complete upper?

A barreled upper has the receiver, barrel, gas system, handguard, and muzzle device installed but no bolt carrier group or charging handle. A complete upper includes both and is ready to pin to a lower. Suppressor-ready versions add a MuzzLok® Plan B compatible flash hider and Faxon’s patented adjustable gas block.

Will this upper fit my lower?

Yes, if it’s a mil-spec AR-15 lower. Mil-spec uppers and lowers share the same pin locations and dimensions. Billet receivers from different makers can fit tighter or looser; Faxon lowers include a tensioning screw to take out play. AR-10, AR-9, and dedicated-lower systems aren’t interchangeable with AR-15 uppers.

Do I need to check headspace?

Every Faxon barrel is headspace gauged with GO/NO-GO gauges when the extension goes on, and the BCG installed is the one this upper ships with. Checking headspace with GO/NO-GO gauges for the bolt you run is always good practice, and it’s a must any time you swap in a different bolt.

What bolt and magazines does a 5.56 upper use?

Bolt: standard 5.56 / M16-pattern bolt (installed). Magazines: Standard AR-15 / STANAG 5.56 magazines.

What ammunition does it shoot?

5.56 NATO and .223 Remington. The 1:8 twist stabilizes 55 through 77 gr.

How do I tune the adjustable gas block?

With the rifle unloaded and the block cool, start fully open and confirm it runs. Close it one click at a time, firing a few rounds per click, until the bolt stops locking back on an empty magazine, then open it one or two clicks. Note the count and retune when you add or remove the suppressor or change to a very different load. It takes a 3/32″ hex key or a flat screwdriver.

What do I need to mount a suppressor?

A Plan B to HUB adapter (titanium $95 or stainless $65, standard or extended) and a 5.56 HUB-mount suppressor, such as Faxon’s HARMONIX® ION 5.56 or HARMONIX® Sentry 5.56.

Why does this upper pair a lightweight BCG with an adjustable gas block?

A lighter carrier needs less gas to cycle, and a suppressor adds back-pressure. Faxon’s rule is that any build with a lightweight carrier gets an adjustable gas block, so you can tune the gas down instead of beating up the carrier, extension, and buffer.

Is a 11.5″ upper legal?

A barrel under 16″ on an AR-15 rifle lower makes a short-barreled rifle under federal law; on a pistol lower it makes an AR pistol. Rules vary by state and locality and can change, so know and follow the laws where you live before you build. Faxon doesn’t provide legal advice.

What makes a good AR-15 upper, and how does this one compare?

Start with the barrel: steel, rifling, finish, and inspection. This one is 4150 CMV, button rifled, QPQ nitrided, borescoped, air gauged, headspace gauged, and 100% MPI inspected. Then a forged 7075-T6 receiver, a gas system matched to the barrel length (mid-length here), a free-float M-LOK handguard, and, on a complete upper, a quality BCG. Faxon makes the barrel, receiver, gas block, and muzzle device, and assembles the upper in Ohio under a Lifetime Guarantee.

Nitride or chrome lining: which is better?

Chrome lining still has its place, mainly sustained automatic fire. For the vast majority of shooters, Faxon’s salt-bath QPQ nitride does what they need and more: it hardens the bore and exterior, resists corrosion, adds virtually nothing to the dimensions (a few ten-thousandths of an inch, about a tenth the width of a human hair), and needs little to no break-in.

Does the upper ship to an FFL?

No. The upper isn’t the serialized part of an AR-15, so it doesn’t require an FFL. Faxon lowers do. State and local laws on barrel length, threaded barrels, and muzzle devices still apply.

Where is it made, and what is the warranty?

Faxon makes the barrel, receiver, gas block, and MuzzLok® devices in Greater Cincinnati, Ohio, and assembles the upper there. It’s covered by the Faxon Lifetime Guarantee.

MuzzLok®, HARMONIX®, CORESYNC®, and Integral® are trademarks of Faxon Firearms. BREEK® is a trademark of its owner. Glock® and Colt® are trademarks of their owners; Faxon is not affiliated with them. “Plan B” is a trademark of Q, LLC; Faxon Firearms is not affiliated with, endorsed by, or sponsored by Q, LLC. Firearm, suppressor, and barrel-length laws vary by state and locality; know and follow the laws where you live.