FAXON REMAGE STYLE MEDIUM SPORTER PROFILE 22" .308 WIN BOLT ACTION BARREL

Rifle Barrels › Bolt Action Barrels › RemAge® Barrels › 22″ Medium Sporter .308 Win  |  Works with: .30 suppressors • 5/8x24 hub adapter

How a RemAge® Barrel Works

A traditional Remington 700® barrel is chambered and shouldered on a lathe to fit one specific action. A RemAge®-style barrel replaces the machined shoulder with a barrel nut, the way Savage® barrels have always worked. Thread the barrel into the action until a GO gauge just closes the bolt, snug the nut against the receiver to lock it there, and check with a NO-GO gauge. The included RemAge® barrel nut is tightened with a standard AR-15 armorer’s (castle nut) wrench.

RemAge® barrels fit factory Remington 700® short actions and similar 700-pattern short actions, and Faxon RemAge® barrels made since December 2023 also fit the Faxon FX7. Because the nut sets headspace, the same barrel works across actions whose bolt-face depth varies.

.308 Winchester, 1:10 Twist

The .308 Winchester is the classic short-action cartridge: easy to find, easy on barrels, and accurate with everything from 150 gr hunting bullets to 175 and 185 gr match bullets. The 1:10 twist is the standard for .308 and stabilizes that whole range.

The Medium Sporter Profile at 22″

The Medium Sporter is a classic sporter contour with more steel than a light hunting barrel. It balances weight and stiffness for rifles you carry and still want to shoot well from a bench, and it is a natural fit for short suppressed builds.

How It’s Made

1. Drill and ream: 416-R stainless bar gun-drilled and reamed
2. Hone: Bore honed to a fine finish before rifling
3. Button rifle: 5R button rifled, 1:10 twist
4. Air gauge: Bore air gauged
5. Stress relieve: Stress relieved after rifling
6. Profile and thread: Medium Sporter profile turned, 1.0625-16 UNEF tenon and 5/8x24 muzzle threads cut, target crown
7. Chamber: .308 Winchester chamber cut
8. Lap: Bore lapped after chambering
9. MPI and nitride: 100% wet magnetic particle inspected, then salt-bath QPQ nitrided inside and out
10. Engrave and inspect: Laser-engraved with the cartridge and twist, then final inspected

Salt-bath QPQ nitride is a diffusion treatment, not a plating. It hardens the bore and exterior and adds corrosion resistance while adding virtually nothing to the dimensions, a few ten-thousandths of an inch, roughly a tenth the width of a human hair. It needs little to no break-in.

How We Inspect It

Faxon barrels are built to a written control plan, and each run is logged on inspection sheets. Here is what this barrel goes through before it ships.

What’s in the Box

What Owners Say

This barrel doesn’t have reviews on FaxonFirearms.com yet. If you own one, tell other shooters how it runs in the review section below.

What Reviewers and Dealer Customers Say

Quotes from third-party reviews and dealer listings; the OpticsPlanet review covers the Faxon RemAge® barrel line, not necessarily this exact cartridge and length.

Build It Out

Other .308 Win Bolt Action Barrels

See every barrel in this line on the RemAge® Barrels page, or browse all Faxon bolt action barrels.

RemAge® 22″ Medium Sporter .308 Win FAQs

What is a RemAge® barrel?

A Remington 700®-pattern barrel that uses a barrel nut to set headspace instead of a machined shoulder. You thread it in to a GO gauge and lock the nut, so you can install it without a lathe.

What actions does it fit?

Factory Remington 700® short actions and similar 700-pattern short actions, plus the Faxon FX7 (on RemAge® barrels made since December 2023).

What tools do I need?

A barrel vise, an action wrench for your receiver, an AR-15 armorer’s (castle nut) wrench for the RemAge® nut, and GO/NO-GO headspace gauges for the cartridge.

What comes in the box?

The barrel and RemAge® barrel nut and thread protector.

Why 416-R stainless and 5R rifling?

416-R machines cleanly and holds a consistent bore. 5R rifling uses five lands with sloped sides instead of sharp corners, which deforms the bullet less and fouls less. Faxon hones the bore before rifling and laps it after chambering for a smooth, consistent finish.

Does a nitrided barrel need break-in?

Little to no break-in. Salt-bath QPQ nitride hardens the bore and resists corrosion and fouling while adding virtually nothing to its dimensions.

Can I run a suppressor?

Yes. The muzzle is threaded 5/8x24. Use a .30 caliber or larger suppressor and confirm alignment before firing.

Where is it made?

In Greater Cincinnati, Ohio, and it is covered by the Faxon Lifetime Guarantee.

Remington® and Remington 700® are trademarks of Remington Arms; Savage® is a trademark of Savage Arms; RemAge® is a trademark of its owner. Faxon is not affiliated with Remington or Savage. HARMONIX® and MuzzLok® are trademarks of Faxon Firearms. Always verify headspace before firing, and know and follow all federal, state, and local laws.