FAXON MATCH-X SERIES TARGET PROFILE 24" RIFLE-LENGTH 6.5 CREEDMOOR AR10 BARREL

What “Honed & Lapped” Actually Means

A barrel bore starts as a drilled and reamed hole. Reaming leaves a surface finish around 32 Ra, which is good enough for a duty barrel and is where most stainless match barrels stop before the rifling button goes through. On a MATCH-X barrel the reamed bore is honed to 8 Ra, a fourfold improvement, before it is button rifled. The point of honing first is the button: it forms the lands and grooves by displacing steel rather than cutting it, and it can only produce a surface as clean as the one it starts from. A profilometer checks the honed finish and a borescope checks for tool marks before the barrel moves on.

Rifling roughens that surface again, and so does everything that follows. The button cold-works the bore at very high pressure, raising the grain along every land edge; the 1150°F stress relief lets the steel relax and leaves a thin surface oxide; and contouring and chambering release more stress and move the bore by a few ten-thousandths. So after all of that machining is done, the bore is lapped back to 16 Ra, polishing lands and grooves together so the bullet sees one uniform surface from throat to crown. For scale, 16 Ra is the finish class of a ground crankshaft journal or a hydraulic valve spool, and it is smoother than the brushed stainless on a refrigerator door, which runs 25 to 40 Ra.

Why it matters: the smoother the bore, the less copper and carbon it holds, the more uniform the friction on every bullet, and the more consistent the velocity from shot to shot. That shows up as tighter vertical dispersion at distance, a shorter break-in, and a barrel that cleans in a fraction of the passes. Faxon then button-rifles the honed bore with 5R geometry, five lands with sloped sides instead of the sharp corners of conventional rifling, which deforms the jacket less and fouls less again.

The other MATCH-X difference is the outside. Match Series barrels are nitrided; MATCH-X barrels are left as bare 416-R stainless, blasted with S110 media for a uniform matte finish. The bore is plugged and the extension, muzzle threads, and gas port are masked during blasting, so the media only ever touches the exterior. Nothing is added to the steel, so nothing can affect the bore, and the matte stainless surface is thermally stable and easy to keep clean. The trade is that bare stainless wants a wipe of oil after wet or humid use, the same as any stainless match barrel.

What’s Included

How It’s Built and Inspected

1. 416-R stainless bar is gun-drilled and pull-reamed from the chamber end, then honed to 8 Ra. Bore diameter is checked with go/no-go pins, finish with a profilometer, and the surface with a borescope.

2. The bore is button-rifled with a 5R, 1:8 right-hand twist (.2575″ bore, .2645–.2665″ groove), then stress relieved at 1150°F for a minimum of four hours. Bore and groove diameters are air-gauged at three points along the length.

3. The blank is chopped, re-centered, and profiled between centers: Target contour, .750″ gas journal held to .0007″, 1-16 extension threads on the 1.200″ chamber journal, 5/8x24 muzzle threads, and the recessed crown.

4. The 6.5 Creedmoor chamber is cut with a go gauge in the machine, verified on a CMM, and borescoped for an even lead with no double step. The rifled, chambered bore is then lapped to a 16 Ra finish, bringing lands and grooves to one uniform surface from throat to crown. Every barrel is magnetic-particle inspected.

5. The nickel-Teflon DPMS-pattern extension is torqued to 150 ft-lb, the gas port is drilled and reamed to .073″, the extension is pinned, and headspace is checked with a 6.5 Creedmoor go/no-go gauge. Finally the exterior is blasted with S110 media for the uniform matte finish, with the barrel plugged and the extension, muzzle threads, and gas port masked so the media never touches a sealing or bearing surface.

MATCH-X 24″ Target 6.5 Creedmoor FAQs

What is the difference between MATCH-X and Match Series?

Both are 416-R stainless with 5R button rifling, a nickel-Teflon extension, and a recessed target crown. MATCH-X adds a bore that is honed to an 8 Ra finish before rifling and brush-lapped to 16 Ra after machining, and leaves the exterior as uncoated, S110-blasted stainless instead of nitride. Match Series is the nitrided, harder-wearing choice; MATCH-X is the smoother-bore, maximum-consistency choice.

What upper, bolt, and magazines does this barrel need?

A DPMS / LR-308-pattern AR-10 upper receiver and barrel nut, a standard .308 Winchester bolt carrier group, and SR-25 / DPMS-pattern .308 magazines. 6.5 Creedmoor is the .308 case necked down to 6.5 mm, so the bolt face, extractor, and magazines are all the same as .308; only the barrel is different. It is not compatible with Armalite-pattern AR-10 uppers or with AR-15 receivers.

What is the Target profile, and what does it weigh?

4.53 pounds. The Target profile carries a full 1.000″ diameter from the 1.200″ chamber journal to the gas block, steps to the .750″ journal, and stays .730″ to the muzzle, the stiffest and heaviest contour in the MATCH-X line. Stiffness is what keeps groups together as the barrel heats through a string, so it is the right choice for a precision rifle shot from a bipod or bench. It is not a barrel for a lightweight hunting build.

What bullet weights does the 1:8 twist stabilize?

Everything 6.5 Creedmoor is loaded with, from 120 gr hunting bullets through the 140 to 147 gr match bullets the cartridge is known for. 1:8 is the standard twist for the cartridge and fully stabilizes the long, high-BC 140, 144, and 147 gr bullets at 24″ velocities, which is what keeps them supersonic past 1,200 yards.

Why 24 inches for 6.5 Creedmoor?

Velocity and consistency. 6.5 Creedmoor was designed around a 24″ barrel, where 140 gr loads reach their advertised 2,700 fps class velocity, and every inch shorter costs roughly 20 to 30 fps. A 24″ Target with a rifle-length gas system also gives the softest, most consistent gas impulse an AR-10 can have, which matters for spotting your own hits at distance. If you want a lighter, handier rifle, this is not that barrel.

Do I need an adjustable gas block?

Faxon recommends one for this barrel. Most 6.5 Creedmoor AR-10s end up suppressed, factory loads vary widely, and large-frame ARs are sensitive to gas volume and buffer weight. The Faxon .750″ adjustable block fits the journal, meters the .073″ port to your load and can, and never puts a screw in the gas path.

What are the two rings behind the muzzle threads?

They are a caliber mark. A 6.5 Creedmoor AR-10 barrel looks identical to a .308 Winchester barrel from the outside, same profile, same 5/8x24 threads, same extension, and the two cartridges use the same bolt and magazines, so it is easy to grab the wrong one off a bench. Faxon machines two rings behind the muzzle threads on its AR-10 6.5 Creedmoor barrels so the caliber can be identified at a glance without reading the roll mark. Two rings means 6.5 Creedmoor.

Do I need to break in a honed and lapped barrel, and how do I care for it?

Less break-in than a conventional barrel; the honed and lapped 16 Ra bore has already smoothed the tool marks that break-in normally shoots out. Clean after the first range session, then shoot it. Because the exterior is uncoated 416-R stainless, wipe it with a lightly oiled cloth after wet or humid use and run an oiled patch through the bore before storage; that is the only maintenance difference from a nitrided barrel.

Is the barrel extension installed and headspaced?

Yes. The nickel-Teflon DPMS-pattern extension is torqued to 150 ft-lb, pinned, and the assembly is checked with a 6.5 Creedmoor go/no-go gauge before it ships. Install it in a DPMS / LR-308-pattern upper with a standard .308 barrel nut and bolt; no additional headspacing is required, though checking headspace with your own bolt is always good practice.

Faxon Lifetime Guarantee. Covers manufacturing and material defects to the original purchaser. Excludes damage from misuse, neglect, improper installation, non-standard ammunition, or modifications. Bore erosion and finish wear from normal use are not defects. Register your product at faxonfirearms.com/product-registration to expedite service. Full terms: faxonfirearms.com/warranty-privacy-terms.

Dimensions and tolerances are nominal from Faxon engineering drawings. Gas block, gas tube, barrel nut, and muzzle device not included. Barrels are firearm components; verify function and headspace with your bolt before firing, and confirm reliable cycling with your ammunition and gas block setting. Teflon® is a registered trademark of The Chemours Company FC, LLC.

For questions, contact customerservice@faxonfirearms.com.